欧美……一区二区三区,欧美日韩亚洲另类视频,亚洲国产欧美日韩中字,日本一区二区三区dvd视频在线

上海鼎振儀器設備有限公司
中級會員 | 第10年

13472521719

當前位置:首頁   >>   資料下載   >>   SAEJ2334實驗室循環鹽霧腐蝕試驗標準

SAEJ2334實驗室循環鹽霧腐蝕試驗標準

時間:2017-9-2閱讀:2900
分享:
  • 提供商

    上海鼎振儀器設備有限公司
  • 資料大小

    28.8KB
  • 資料圖片

    查看
  • 下載次數

    234次
  • 資料類型

    JPG 圖片
  • 瀏覽次數

    2900次
點擊免費下載該資料

 

 

SAE J2334 上海鼎徵儀器儀表設備有限公司

 

The Automotive Cyclic Corrosion Test

Introduction

By the 1980’s rapid growth of vehicle ownership and poor customer experience of corrosion resistance during the preceding 20 years, had given motor vehicle manufacturers and their component suppliers a significant issue to address. The industry required a more predictive method of testing which would allow component performance to be addressed before field trials and product releases. One method of testing which was shown to be particularly indicative of the performance of components in the conditions in which vehicles operate was the Cyclic Corrosion Test (CCT).

As a result of early experience, the automotive industry took a lead role in the development of cyclic corrosion tests with the objective of producing results that better correlate with field exposure. In 1984, The Automotive Corrosion and Prevention Committee, in collaboration with the Corrosion Task Force of the American Iron and Steel Institute and the Society of Automotive Engineers, began its work. This group strived to develop the knowledge of corrosion mechanisms and their replication in a controlled environment until, nearly 20 years later and after considering over 130 available laboratory, proving ground, and outdoor corrosion tests, the SAE Surface Vehicle Standard, J 2334 Cosmetic Corrosion Lab Test, was published in June 1998.

The development of SAE J2334 was time consuming, but thorough. Ten substrate materials were selected for use in the tests to reflect the materials most commonly used and/or   subject to the greatest corrosive damage in vehicle applications.. At least two substrates were chosen because the existence of proven corrosion testing results enabled them to be used to assure the consistency of the test. Canadian on-vehicle tests were conducted at Montreal, Quebec and St. John's Newfoundland for 5 years. The test panels were mounted on the vehicles in both horizontal and vertical orientations to better represent the various surface orientations typically found in vehicle applications. The corrosion mechanisms of on-vehicle and laboratory tests were studied by Lehigh University, and the resulting analysis showed that similar corrosion products and modes were found in these tests as were found after conducting SAE J2334 tests.

Test Conditions

Test specimens are placed in an enclosed chamber and exposed to a changing climate that comprises of the following 3 part repeating cycle.

  1. 6 hours exposure to a water fog/condensing humidity climate of 100%RH at +50C.
  2. 15 minutes immersion in (or a direct spray of) salt water at ambient.
  3. 17 hours 45 minutes of air drying in a climate of 50%RH at +60C.

For the specimens a minimum of 6, each sized 25.4 x 50.8 mm and made of AISI 1006-1010 steel, are used.

The test cycle is repeated daily, fully automatic cabinets have the option of running during the weekends or programming in a dry stage soak.

The number of cycle repeats and therefore the test duration is variable.

The 100% relative humidity wet stage condition can be achieved by one of three methods shown as follows. Whichever method is employed, test samples and controls are required to be visibly moist/wet.

  1. Wet-bottom method according to ASTM D2247 – except that the temperature shall be 50C +/-2oC.
  2. Water fog method according to ASTM D 1735, except that the collection rate is reduced from a range of 1.5 to 3ml/h to 0.75 to 1.5ml/l.
  3. Steam (Vapour) method.

The samples must be subject to an application of salt solution consisting of the following formulas and by use of one of three methods shown as follows;

0.5% NaCl

0.1%CaCl2

0.075% NaHCO3

a. Immersion Method – test specimens immersed in the salt solution for a 15 minute interval of each test cycle.

b. Spray Method – periodic or continuous direct impingement spray of the salt solution over the 15 minute interval that ensures that the test specimens are kept wet for the entire 15 minute interval.

c. Air Atomised Fog Method –15 minute exposure to atomised fog provided the fog collection rate is 2ml/hr to 4ml/hr instead of 1ml/hr to 2ml/hr.

Note that either the CaCl or the NaHCO3  material must be dissolved separay in deionised water and then added to the solution of the other materials otherwise an insoluble precipitate may result.

Typical Applications

SAE J 2334 is used widely throughout the North American automotive industry - particularly by General Motors and their suppliers.

It is also used elsewhere in the world where these auto companies have salite manufacturing facilities, or joint collaborative ventures with other auto manufacturers. 

 

會員登錄

×

請輸入賬號

請輸入密碼

=

請輸驗證碼

收藏該商鋪

X
該信息已收藏!
標簽:
保存成功

(空格分隔,最多3個,單個標簽最多10個字符)

常用:

提示

X
您的留言已提交成功!我們將在第一時間回復您~
撥打電話
在線留言
国产午夜福利片无码视频| 非洲大鸡巴操逼黄色录像| 3色w九九久久男人皇宫宕| 美女被插b在线观看| 插插插插插插插插插插插| 国产亂倫近親相姦| 国产欧美一区二区精品久久久| 中文欧美亚洲欧日韩| 日韩亚洲AV无码一区二区不卡| 白嫩在线亚洲观看| 国产成人AV一区二区在线观看| 久久亚洲精品中文字幕一| 亚洲国产成人手机版| 18岁美女破处在线观看| 让女人下面出水视频| 国产精品熟女一区二区三区久久夜| 美女骚逼黄色18禁| 日本免费精品一区二区三区四区| 亚洲精品伦理熟女国产| 亚洲激情无码视频| 中国老女人 操逼 视频| 夜色成人免费观看| 999久久久国产大美腿| 91秦先生全集在线观看| 三男狂插小穴穴视频| 公交车上被后入搞逼漫画| 欧美一区二区三区久久国产精品| 男人扒开女人腿狂躁免费| 男人的天堂日本在线观看| 国产精品熟女一区二区三区久久夜| 肏亚洲女人小骚逼| 少妇精品久久久一区二区免费| 亚洲另类激情在线观看| 欧美 日韩 国产 自拍| 五月天亚洲激情综合av| 国产精品粉嫩懂色av| 日本一区二区三区高潮喷吹| 国产在线麻豆精品| 国产精品欧美久久久久久| 日韩欧美一二三区| 美国大鸡巴操逼视频|